 |
|
Last update October 10, 2004
|
Factory Service
Schedule
Don't throw away those worn out or broken Relton bits
and saws!
In most cases, we can repair the bit to an almost new condition
for a
fraction of the cost of a new bit!
Sorry, we repair Relton products only.
| Factory Service Info | Hammer Bits |
|
Hole Saws & Rebar Cutters | Core Bits
& Hard Head Bits |
| Repair Kits for
Quik-LokTM ADAPTORS |
| Navigator |
|---|
Factory Service Info
|
will forward it on to the factory, or you can send it directly to :
| Relton
Corporation 317 Rolyn Place Arcadia, CA 91007 Tel: (323) 681-2551 Fax: (818) 446-9671 |
Master Index
| Diameter | Regrind Only | Replace Carbide | Remill* |
|---|---|---|---|
| 1/4" thru 7/16" | $3.00 | - | - |
| 1/2" thru 5/8" | 3.50 | $13.50 | $17.00 |
| 11/16" thru 3/4" | 4.00 | 13.00 | 18.00 |
| 27/32" | 4.00 | 14.00 | 18.00 |
| 7/8" thru 1" | 4.50 | 18.00 | 21.00 |
| 1-1/8" thru 1-1/4" | 5.00 | 25.00 | 31.50 |
| 1-3/8" | 5.50 | 25.00 | 32.00 |
| 1-1/2" | 6.00 | 30.00 | 36.00 |
* Cross-Top cannot be remilled.
| Back to top | Factory Service Info |
Master Index
Factory Service
Brazed-Carbide Hole Saws
& Rebar Cutters
| Diameter | Regrind | Replace Carbide & Regrind |
|---|---|---|
| 1/2" thru 11/16" | $6.50 | $4.00 each carbide + $6.50 regrind |
| 3/4" thru 1-3/4" | 7.50 | 4.00 each carbide + 7.50 regrind |
| 1-7/8" thru 2-3/4" | 8.50 | 4.00 each carbide + 8.50 regrind |
| 3" thru 4" | 11.00 | 4.00 each carbide + 11.00 regrind |
| Porcelain Cutter Kits | 15.00 | 4.00 each carbide + 15.00 regrind |
| Porcelain Cutter Kit Components | see
corresponding sizes above |
see
corresponding sizes above |
| All Carbide-Tipped Pilots | 3.00 | Regrind only available |
| Back to top | Factory Service Info |
Master Index
Factory Service
Hammer Core Bits & Hard
Head Bits
| Diameter | Regrind | Replace Carbide & Regrind |
|---|---|---|
| 1/4" thru 7/16" | $4.00 | - |
| 1/2" thru 5/8" | 4.00 | $3.00 each carbide + $4.00 regrind |
| 11/16" thru 3/4" | 4.50 | 3.00 each carbide + 4.50 regrind |
| 7/8" | 5.00 | 4.00 each carbide + 5.00 regrind |
| 1" | 6.00 | 4.00 each carbide + 6.00 regrind |
| 1 1/8" thru 1 3/8" | 6.50 | 4.00 each carbide + 6.50 regrind |
| 1 1/2" | 7.00 | 4.00 each carbide + 7.00 regrind |
| 1 5/8" thru 1 3/4" | 7.50 | 4.00 each carbide + 7.50 regrind |
| 2" thru 2 1/4" | 8.00 | 4.00 each carbide + 8.00 regrind |
| 2 1/2" thru 2 3/4" | 8.50 | 4.00 each carbide + 8.50 regrind |
| 3" | 9.00 | 4.00 each carbide + 9.00 regrind |
| 3 1/2" | 9.50 | 4.00 each carbide + 9.50 regrind |
| 4" | 11.00 | 4.00 each carbide + 11.00 regrind |
| 4 1/2" | 11.50 | 4.00 each carbide + 11.50 regrind |
| 5" | 12.50 | 4.00 each carbide + 12.50 regrind |
| Back to top | Factory Service Info |
| Navigator |
|---|
Send your orders, comments and questions to us, all comments are welcome.
| Q & A@BarrettDiamond.com | SALES@BarrettDiamond.com |
|---|
